Home › Brand Directory › TP-Link
Hardware Engineering Reference (2026 Edition)

TP-Link Router Admin Login & Default Credentials

Complete technical setup guide for TP-Link networking equipment. Access your gateway dashboard at 192.168.0.1 or tplinkwifi.net, retrieve verified credentials, and configure Wi-Fi security.

Quick Answer: How to Log Into Any TP-Link Router

Connect your device to your TP-Link Wi-Fi network (SSID format: TP-Link_XXXX or Deco_XXXX) or connect an Ethernet cable to LAN Port 1. Open any web browser and go to http://tplinkwifi.net or http://192.168.0.1. Enter factory default username admin and password admin.

Live Gateway Diagnostic Console
Console Idle

Test whether your device is currently connected to a TP-Link gateway at 192.168.0.1 or http://tplinkwifi.net directly from your browser.

Open 192.168.0.1 Dashboard →

TP-Link Router Models & Default Credentials

Verified factory default IP addresses, admin usernames, and passwords for TP-Link hardware:

Swipe left/right to view all columns →
Hardware Model Default Gateway IP Default Username Default Password Technical Notes
TP-Link
Archer AX50, AX55, AX73, C7, AX10, C6
http://tplinkwifi.net
 admin admin (or user-created) Modern firmware prompts to set a new password on first boot.
TP-Link
TL-WR841N, TL-WR940N, TL-WR840N
http://192.168.0.1
 admin admin Classic budget TP-Link routers. Default user and pass are both admin.
TP-Link
Deco Mesh M4, M5, X20, X50, X60, XE75, BE85
TP-Link Deco App
 TP-Link ID Email User Cloud Password TP-Link Deco uses 192.168.68.1 subnet. Setup and control via Deco mobile app.

Step-by-Step TP-Link Admin Setup Guide

1

Connect to TP-Link Local Network

Connect your PC, smartphone, or tablet to the router network via Wi-Fi (SSID format: TP-Link_XXXX or Deco_XXXX) or plug an Ethernet patch cable into any numbered LAN port (1 through 4). Avoid connecting to guest networks.

2

Launch Browser & Enter Gateway IP

Open Chrome, Safari, Firefox, or Edge. In the top URL address bar, enter http://tplinkwifi.net or http://192.168.0.1 and press Enter.

3

Input Factory Admin Credentials

When prompted by the authentication dialog, enter default username admin and password admin. If these fail, check the printed serial label underneath your device or perform a hardware reset.

4

Update Admin Password & Configure Wi-Fi

Immediately navigate to Administration / System Settings and replace the default password with a cryptographically secure key. Proceed to Wireless Settings to configure WPA3-Personal security.

How to Factory Hard Reset a TP-Link Router

If you forgot your customized admin password or experience firmware corruption, you can restore factory defaults using the physical hardware reset procedure:

Important Notice: Configuration Erasure

A factory reset permanently erases all customized Wi-Fi network names (SSIDs), passwords, port forwarding rules, static DHCP reservations, and custom DNS settings. Your router will revert to factory defaults.

  1. Verify your TP-Link router is plugged in and the Power LED light is solid.
  2. Locate the recessed Reset pinhole button on the rear or bottom panel.
  3. Insert an unfolded paperclip or SIM-ejection tool and press the button firmly for 10 seconds.
  4. Watch the LED indicator lights blink, indicating the flash memory reset sequence has initiated.
  5. Release the button and allow 2 to 3 minutes for the system to complete its automated reboot cycle.
  6. Reconnect using factory default credentials: username admin and password admin.

Frequently Asked Technical Questions

Most TP-Link Archer and wireless routers use 192.168.0.1 or 192.168.1.1 as their default IP. You can also access the admin page via the local domain http://tplinkwifi.net without typing numbers.

TP-Link Deco systems operate on 192.168.68.1 by default. While you can open http://192.168.68.1 or http://tplinkdeco.net in a browser, full management is handled via the TP-Link Deco mobile app for iOS and Android.

Ensure your device is connected directly to your TP-Link Wi-Fi or LAN cable. If you are on cellular data or an active VPN, disable it, then navigate directly to http://192.168.0.1 instead of the domain name.

With the router powered ON, use a paperclip to press and hold the recessed RESET button on the back panel for 10 seconds until the system LEDs flash simultaneously, then release.